Sale!

Seina Half Brick IP44 2W Cool White 316 Stainless Steel

Seina Half Brick IP44 2W Cool White 316 Stainless Steel - Image 2

Seina Half Brick IP44 2W Cool White 316 Stainless Steel - Image 3

Seina Half Brick IP44 2W Cool White 316 Stainless Steel - Image 4

Seina Half Brick IP44 2W Cool White 316 Stainless Steel

Original price was: $31.82.Current price is: $22.27.

SKU: ZXH0Z 1704332455 Categories: Outdoor Lights, Step & Brick Lights

Free and fast shipping worldwide
Experience the Best Quality
Online assistance, always at your service.
Shop with confidence, we guarantee quality.

Seina half brick IP44 2W cool white 316 stainless steel – 220 – 240v

The Seina half brick is the ideal outdoor fitting for smaller properties where space is scarce. Available in a black.

Manufactured from marine grade stainless steel
Marine grade brushed stainless steel & frosted pc
Constructed from marine grade stainless steel (316) & polycarbonate
2W LED module (SMD 2835) Cool White (Included)
K: 4000 Lm: 100 Lm/W: 50
IP44
Proj: 2mm H: 85mm W: 122mm
Class 2
Cut hole: 103x65mm
2+1YR Extended Warranty
Weight: 0.4 Kg

A guide to lighting steps

Lamp colour ( Kelvins )

The colour of a lamp is defined as a measurement called kelvins. A standard GLS incandescent bulb in the home would be
2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white
spectrum.

Installation 220 – 240v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how
it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting
and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the
products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be
made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then
filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and
reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially
in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light. Mains 240v cable
will have less joints than a low voltage installation but care must be taken with the cable runs. Cabling should be Rubber
Butyl and not PVC. PVC leads to capillary action over time especially with UV degradation.

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with
Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site.

Using a single RCD for large numbers of 240v fittings is not recommended due to the risk of nuisance tripping. We advise the use of separate RCD protection for each circuit and a maximum of 12 fittings per RCD. Where a garden lighting installation of more than 12 spike mount or recessed lights per circuit is proposed, we suggest the installation of 12v units with transformers, which results in a significantly higher fault tolerance and reliability in the total installation.

Colour	Black, Silver
Lumens	100 lm
Bulb Type Bulb type used for fittings	Integral LED
Class	class 2
Colour Colour of fitting	Silver
Height	85mm
IP Rating Ingress Protection - a two digit code representing water resistance.	IP44
Colour Temperature	4000k
Materials	Stainless Steel
Projection	2mm
Voltage Voltage of fitting, Light Bulb or Transformer	240v
Warranty	2 Years
Watts	2W
Width	122mm